Видео

Dude thanks for the help. What’s the song name? 🔥

I agree excellently explanation! San Antonio, Texas

I have followed over 20 inlay videos, step for step, and it never works. It mostly puts the plug and pocket on top of each other, even if I do what board at a time. Then there's the error crap, tool path won't cut anything crap. STEP FOR STEP AND IT NEVER WORKS.

GREAT VIDEO GUYS!

GE GSCS3KGYAFSS. Mine was just wet, all pins were intact. I cleaned everything with CRC QD Electronic Cleaner, put some Super Lube 21030 Synthetic Grease in the connector, then heat shrinked it. Good as new. Video was awesome, thank you!

Thank You that was spot on, as you said because of condensation the little black connector on of the wires had moisture for years and was oxidized and broken, I cut off connector and used sta-kon wire nuts to remake connection. 30 minute repair saved a wad of dollars.

So I don’t have the wires in that spot. Nothing down there with my model

THANX RUclips FOR FUCKING UP ANOTHER VIDEO WITH A MIRIAD OF RELENTLESS FUCKING ADDS

Nice idea! Will probably do somethinglike this

👍

You didn't show taking off the heater hose by the firewall

A good video. Would be better if you removed the "toadly rad" music.

Does this work if the screen has gone black?

Can these be adapted to tubular steel? I have same issue with ID 40.8mm

my school mechanical shop did my Ford 1 broke I guess I was super lucky 2 trick warm engine run seafom through first

Can you use a slapper on a motorcycle tank without a dolly?

I bought the Seams Impossible tool but I have a questions. The side screws to affix the tool in the jackets don’t line up. The screw hole in the tool is closer to open edge of the jacket. I can see the majority of the screw hole in the tool. So can I adjust the screw holes in the jackets, making them slight oval versus round?

On my 1997 5.4 the #7 coil pack and plug has been replaced 2 times in 2 months (1st time I changed all the CP & SP). When the last one had to be changed I was told the hole the retaining bolt goes in was striped. I can definitely wiggle the CP head when it’s “bolted down”. It runs fine for a while but 5 weeks since the last change I’m getting the PO307 code again and again after I clear it. Could the bolt that secures it being loose and therefore the cp head being loose be cause the problem?

So when installing the new sensor do i have to put it in the little slot or does it just sit on top of it?

Sorry for commenting on a 9 year old video. Is there a specific reason to have the transformer near the pickup in a circuit like this? Could I say mount the transformer further away like on a pedal board and just run the output from my guitar to the transformer via guitar cable first before bringing it into the rest of my signal chain?

Nice build man!

Engineers get pretty bored sometimes, The design engineer of this spark plus setup has a brother who sells the repair kit....LOL

That ceramic probe you have. Last week I went to load my haimer in my machine and the taper seating popped the head right off the probe lol 60 bucks gone 🤦‍♂️

Less is more

The 2009 and 10’s are a completely different story as the valve covers have to come off to change these after the redesign.

Did not work on my 2009. Solenoid will not come out without removing the valve cover!

Its galvanic corrosion. I replaced the valves before I saw your video. GE used metal and nonmetal together ferrous and non ferrous You cant do that the electrolite was the water vapor in the air being drawn across it by the condensor fan. Bad GE it should have never happened someone saved a couple of dollars. Never put metal and non metal together thats what happens...

I know this is an older video, but would this replacement fix screen vignetting? I only have a tiny circle of visibility left on my screen lol

Time well spent.

I’m in the middle of doing this job and omg!! Dropped my 7mm socket in bell housing, had to drop the starter and make a magnet to fish it out. Woosah

Wow. Can we purchase one of these?

Cool and I was worried about cutting a 3mm sheet, thats about 1/8 inch. I'll give it ago tomorrow, luckily my tiny shed is seperate to the house but I'll do my best to reduce the mess.

how thick is that pipe ?

0:58 my boss when I was grinding out cracks in a fucked up rim for a temp fix.

Looks fantastic. Thank you for sharing your video and information. God bless 🙏

So the F250 fuel rail doesn't have a schrader valve to release the fuel pressure or hook up a fuel pressure guage?

A grinder and paint makes me the welder I ain’t

Good vide and information if you have time to get through alllllll the unnecessary chatter.

LOL Good laughs!

These look super interesting! Does each individual 'coil' require its own transformer?

I just received my tool. Works. Like. A. Charm. Every buck you earn with it is well deserved. Nothing more to say.

Greg's Garage needs a hydraulic lift

Have a 07 5.4 3v flex fuel. Which brand fuel injectors do you recommend? Btw, music is fine.

My GE refrigerator isn't the same model as yours in the video, but basically the same connections behind the lower plastic panel. Thanks to your video, I went straight to the problem. The connector was corroded! Not as badly as your though, so I was able to avoid the cutting and resoldering of the wires. I cleaned up the individual connections to get as much of the corrosion off as I could. I then applied some moisture preventative dielectric lube to the connector and reconnected it. Problem solved! Total repair time was about 15 minutes. Thank You!!

Nice! Thank you for the idea. Do you have experience with continous usage of the tool? I mean did you tried to use this tool on more ocassions? Or this is good for home or amateur usage?

I need the jose diagram anybody know where I could get it for 98 Ford q50 5.4 liter

This does not work on the 2010 5.4L. You have to remove the valve covers.

Great video! I did this but my camera wont turn on now. How could I troubleshoot?

fucking 3V

Great video! Are there any long term negative side-effects on the neck with this kind of storage? I see that the body is slightly raised as each guitar sits in the cradle. I ask because when in a case the angle produced by the cradle is lower and was wondering whether there is any long term negative side-effects to the neck and if so how to mitigate them. Thanks in advance to you or anyone who kindly responds.